Skip to main content
Painting & Flooring

Timber Floors That Cup Or Lift After A Leak

John OwenFounder4 min read

Timber floorboards cup after a leak because they have taken up water from underneath. The bottom of each board swells more than the top, so the edges rise and the middle dips. The repair starts with stopping the leak and drying the floor slowly, and the moisture is measured before anyone sands, because a floor sanded while it is still wet ends up worse.

Many cupped solid timber floors settle back far enough to be sanded and recoated. Boards that have buckled, split or started to rot are replaced.

Cupping, crowning and buckling

Cupping is the edges of each board sitting higher than the centre. It means moisture below the boards, from a leak, a wet subfloor or a damp concrete slab.

Crowning is the opposite, with the centre higher than the edges. It shows up when a cupped floor was sanded flat before it dried. As the boards dry, the bottom shrinks back, and the sanded edges end up lower than the centre.

Buckling is a section of boards lifting clear off the joists or the slab. It takes a lot of water, and those boards come up.

The source of the water

Find the source before anything else. In a house or terrace with a crawl space, look under the floor for a dripping pipe or pooled water. In an apartment with boards laid over a slab, the water comes from above or beside the floor: a dishwasher, a fridge water line, a flexi hose, a shower leaking sideways under a wall, or a balcony door letting rain in.

A floor that cups beside a bathroom or kitchen with no drip in sight is treated as a hidden leak until the plumber has proved otherwise.

Drying it out

Timber dries slowly, and the slower it dries the more evenly it settles. Keep the room open, keep air moving with fans and let a dehumidifier draw the moisture out over days and weeks. A heater aimed at the floor dries the top faster than the bottom, and that splits boards.

Where there is a crawl space, the subfloor needs air too. Blocked vents and damp soil keep the boards wet from below, as covered in [sub floor ventilation and timber rot](/blog/sub-floor-ventilation-and-timber-rot).

Measured before it is sanded

A moisture meter decides when the floor is ready. The damaged boards are measured against an untouched part of the same floor, and sanding waits until the two read the same.

Only then is the floor sanded and recoated. A floor that has settled flat sands back like any other, as described in [timber floors, sand or replace](/blog/timber-floors-sand-or-replace).

Engineered, laminate and hybrid floors

Engineered timber has a thin timber layer over a plywood or composite base. It cups like solid timber, but there is only so much timber on top to sand, so a badly cupped engineered floor is replaced rather than sanded back.

Laminate has a fibreboard core that swells at the joints when it gets wet, and that swelling is permanent. The planks with raised edges come out.

Hybrid planks have a waterproof core, so the planks themselves survive. The water sits under them, on the underlay or the slab, and the floor is lifted so the base can dry and no mould is left sealed underneath.

Boards that come out

Boards that have split, rotted or buckled are replaced one at a time with matching timber, so the repair blends into the floor around it. On a polished floor, the whole room is then sanded and coated together so the colour reads as one surface.

Photos for the claim

A leak that damages a floor is often an insurance matter. Photograph the cupping before anything is moved, keep the moisture readings and keep the plumber's report on the leak. The repairs that tend to drop out of a claim are covered in [insurance repairs and the scope that gets missed](/blog/insurance-repairs-and-the-scope-that-gets-missed).

The order of work

Plumbing first, then drying, then carpentry on the damaged boards, then sanding and coating last. With one team holding that order, nobody sands a floor that is still wet, and the skirting and paint that took the same water are repaired in the same programme of work.

Our flooring work. Talk to us about a property.

JO

John Owen

Founder

Ample Trade, every trade a property needs held by one accountable team on one contact, across the Eastern Suburbs and the Sydney CBD.

FlooringTimber FloorsLeaksInsuranceRepairs

Tell us about your building.

We will respond with a clear understanding of how we can help.

Get in Touch