Skip to main content

Our services.

One contact handles the whole list.

Maintenance

One contact for any problem the building throws at you.

Maintenance, Ample Trade

Every trade a property requires, as it requires it, delivered by one accountable team through a single point of contact. A tenant reports a fault, a building manager finds a problem, or a hotel room needs attention, and the works list comes to Ample rather than to four separate vendors. Faults are diagnosed at the cause and repaired once. Urgent work involving water, power or security is attended first, by the team that holds every other trade on the property.

Repair and fault resolution across every trade a building needs
One list of works handled on one account
Urgent faults handled fast, water, power and security first
End-of-lease make-good and between-tenancy turnover
The connective make-good layer that ties a job together
Correctly diagnosed the first time, so the fault does not come back

Electrical

One line on the list, not a vendor to chase.

Electrical, Ample Trade

Power points, lighting, smoke alarms, switchboard and circuit work, fault-finding and final fit-off, delivered by the same accountable team that holds every other trade on the property. An electrical fault does not become a separate vendor to source, vet and coordinate. It is one line on the same works list, completed to the same standard, with the board left in better order than it was found.

Power points and dedicated appliance circuits
Lighting, LED retrofits, downlights and fans
Hardwired interconnected smoke alarms
Switchboard, circuit and safety-switch work
Fault-finding and nuisance-trip resolution
Oven, cooktop and hot-water electrical connection
Rewires and final-fix fit-off

Plumbing & Gas

The leak is fixed once, and the area is handed back dry.

Plumbing & Gas, Ample Trade

Blocked drains, leak detection, taps and mixers, toilets and cisterns, hot water and fixture work, delivered by one accountable team. Leaks are traced to the source rather than treated at the symptom, and any damage caused on the way is repaired by the same team. A leaking toilet is reseated with new seals and tested, not temporarily adjusted, so the repair holds.

Blocked drains and drain inspection
Leak detection and repair
Taps, mixers, valves and fixture replacement
Toilet and cistern repair and replacement
Hot water repair and replacement
Isolation and tempering valves
Gasfitting where licensed

Climate & Air

Comfort you never have to think about again.

Climate & Air, Ample Trade

Split-system supply and installation, routine servicing and fault diagnosis, delivered by the same team that holds the rest of the property. Air conditioning sits across electrical, plumbing and building work, so the circuit, the wall penetration and the condensate drain are set correctly at the outset. A blocked condensate line causes water damage in the unit below when it is left to a single trade.

Split-system supply and install
Routine servicing and filter cleaning
Condensate-drain clearing
Fault diagnosis, thermostats and controls
Ducted comfort and climate control
The circuit side handled by the same team

Building & Interiors

The space is handed back looking untouched.

Building & Interiors, Ample Trade

Cabinetry fit-off, vanity and benchtop installation, wall patching, sealing, and the interior repairs that sit between trades. This is the work that returns a space to the condition it was in before the works began, and it is where a standard above the client's own is most visible, because it is the work most easily rushed. Scope is interiors and refurbishment. New builds sit outside it.

Cabinetry and fit-off make-good
Vanity and benchtop coordination
Sealing, silicone and general patching across a job
Between-trade making good after wet or electrical work
Interior refresh work, never new builds
The connective layer that ties a whole job together

Carpentry

Doors, timber and joinery that sit right and stay right.

Carpentry, Ample Trade

Door hanging and adjustment, skirting and architraves, timber repairs, joinery refits and second-fix carpentry, delivered by the same accountable team that holds every other trade in the building. A door that will not close, or a damaged run of skirting, is one line on the same works list. Work is measured, fitted and finished so it matches the existing detail, with hardware that operates correctly on handover.

Door hanging, adjustment and hardware
Skirting, architraves and shelving
Timber and second-fix carpentry repairs
Joinery repair and refit
Window adjustment, mounting and fixing
Minor structural timber repairs, never new builds

Tiling & Waterproofing

Sealed underneath, laid level on top, and it never leaks again.

Tiling & Waterproofing, Ample Trade

Floor and wall tiling, re-tiling and grouting, and the waterproof membrane beneath it, owned by one accountable team. A wet area performs only as well as the membrane and the falls under the finish, and a leaking shower sits across plumbing, tiling and waterproofing. Where three vendors attend, none of them owns the outcome. Ample holds all three, so the membrane is confirmed before the first tile is laid.

Floor and wall tiling, re-tiling and feature walls
Wet-area waterproofing and membrane detailing to standard
Leaking-shower rectification, owned end to end
Substrate prep, screed and falls to the waste
Shower strip-out, re-membrane and re-tile in sequence
Grouting, re-grouting and silicone fit-off
Water testing before handover

Painting

The repaint that reads new on the first walkthrough.

Painting, Ample Trade

Interior preparation, patching, cutting-in and topcoats, the late-stage trade that returns a stripped and reworked property to a condition ready to re-list. Paint is the first finish a tenant or a buyer sees, so its position in the programme matters out of proportion to its size. It is applied after the dust-generating trades and before final fit-off, by the same team that completed the patching.

Interior repaint, prep, patch and topcoats
End-of-lease repaint, ceilings, walls and trim
Feature walls and colour matching in occupied property
Cutting-in on doors, frames and skirting
Surface prep after patching and make-good
Painted in sequence, after the dust-making trades

Flooring

Laid last, so the new surface is handed over untouched.

Flooring, Ample Trade

Carpet, timber, hardwood and hybrid flooring, installed at the end of the programme so the finished surface is not walked through by another trade. The floor is what a tenant or a buyer feels underfoot on the first inspection, and it presents correctly only when the subfloor preparation, the underlay and the transitions are right. One accountable team sequences it after every dust-generating trade.

Carpet, timber, hardwood and hybrid flooring
Subfloor prep, underlay, transitions and trims
Removal and disposal of old floor coverings
Floor levelling and moisture checks before laying
Skirting reinstatement and edge finishing
Laid last in the sequence, so the new surface stays new

Handyman

The whole list of small jobs, closed by one team.

Handyman, Ample Trade

The sticking door, the loose towel rail, the blown downlight, the tap that drips, the shelf that pulled out of the wall. Individually none of them is worth a trade call, which is why they sit on a property for months and turn up in an inspection report all at once. They go on one list, get closed by one team in one attendance, and come back as one line on the works order. The handyman layer is the work that is easiest to rush, so it is the clearest place a standard shows.

Doors that stick, drop or will not latch
Shelving, rails, hooks and fixings that pulled out
Patching and make-good after another trade
Tap washers, seals and running cisterns
Flyscreens, window hardware and sliding tracks
Lights, fans and fittings swapped out
The end-of-lease defect list, closed in one attendance

Cabinetmaking & Joinery

Cabinetry that reads original, not repaired.

Cabinetmaking & Joinery, Ample Trade

Kitchen and vanity cabinetry, wardrobes, benchtop coordination, and the make-good that closes a cabinet after plumbing or electrical work has been through it. When an appliance goes in where one was never fitted, the cupboard has to be cut, rebuilt and finished so nothing about it looks adapted. The team that opens the cabinetry is the team that closes it, so there is no patch and no gap between two trades. Square reveals, flush faces, consistent gaps and scribe lines tight to walls that are never straight.

Kitchen and vanity cabinetry repair and refit
Cupboard rebuild and make-good after appliance work
Wardrobe and storage joinery
Benchtop coordination and fit-off
Doors, drawers, runners, hinges and soft-close hardware
Scribes, reveals and trim to out-of-square walls
Water-damaged carcass and kickboard replacement

Locks & Door Hardware

The lock is changed before the next tenant has the key.

Locks & Door Hardware, Ample Trade

Rekeys between tenancies, deadlocks and entry sets, door furniture, strikes and closers, and the door itself when the hardware was never the real problem. On a changeover the lock is one of the few items with a hard deadline attached to it, because the new tenant cannot be handed a key that the last one still has a copy of. It sits on the same works list as everything else on the property and gets closed in the same attendance.

Rekeys and lock changes between tenancies
Deadlocks, entry sets and privacy sets
Door furniture, handles and escutcheons
Strikes, latches and alignment after a door has dropped
Door closers on common-area and fire doors
Window locks and sliding-door locking
Keyed-alike sets across a building

Glazing & Window Repair

The pane is made safe the same day and replaced properly.

Glazing & Window Repair, Ample Trade

Cracked and broken panes, failed seals, window and sliding-door hardware, and the make-good around the opening once the glass is in. A broken window in an occupied property is a security problem before it is a repair, so it is made safe first and replaced properly after. Sliding doors that have stopped running are usually rollers and tracks rather than glass, which is the kind of distinction that decides whether the job is an hour or a replacement.

Cracked and broken pane replacement
Making a broken opening safe and secure
Failed double-glazed and fogged units
Window and sliding-door rollers, tracks and stays
Sashes, winders and restrictors
Shower screens and mirrored glass
Reputtying, beading and make-good around the opening

Plastering & Gyprock Repair

A patch that disappears instead of a patch you can find.

Plastering & Gyprock Repair, Ample Trade

Holes, cracks, water-damaged sheet, cornice and the set work that follows any trade opening a wall or ceiling. A plaster repair either disappears or it advertises itself under the first coat of paint, and the difference is almost entirely in the preparation and the number of coats. The team that cut the wall for the plumbing or the cabling is the team that closes it, so the opening and the finish are one scope rather than two attendances and a blame trail.

Patching after electrical, plumbing and cabinetry work
Sheet replacement where water has been through it
Cracks at joints, corners and settlement lines
Cornice repair and replacement
Ceiling sheet replacement and re-fixing sagged sheets
Set, sand and prepare ready for paint
Access panels made good after service work

One contact covers every trade.

Send through what the property needs and we will respond with a clear plan and a quote to keep it running.