Squeaky Floorboards And How They Are Fixed
Floorboards squeak when a board moves under a foot and rubs against the board beside it, or slides up and down on a loose nail. The fix is to stop that movement, most often by screwing the board down firmly to the joist or batten underneath.
How that is done depends on what the floor is and what sits below it. A terrace with a crawl space, an apartment with timber laid over a concrete slab and a floating floor all squeak for different reasons, and each one is fixed a different way.
Why boards start to move
Timber moves with the weather. In a dry winter with the heating running, boards shrink and small gaps open between them. Through a humid Sydney summer they swell and tighten again, which is why some squeaks come and go with the seasons.
Nails lose their grip over the years as well. Every step pushes a board down and lets it spring back, the nail hole slowly widens, and in the end the board rides up and down the nail. That is the classic squeak in an older timber floor.
The joists play a part too. Over decades a joist can shrink, twist or sag a little away from the boards above it, and wherever that happens the boards are left bridging a gap with nothing solid underneath to stop them flexing.
Where the squeak is
Walk the floor slowly and mark each squeak with a strip of tape. Most of them sit on a joist line, and the rows of nail heads across the boards show where those joists run.
A soft, springy or dipping spot is a different problem. Near a bathroom, a kitchen or an outside door it points at a leak or rot underneath, and screwing it down only hides the cause. The signs are in [sub floor ventilation and timber rot](/blog/sub-floor-ventilation-and-timber-rot).
Nailed timber floors
Houses, terraces and many older apartment blocks have their boards fixed straight to the joists.
From above, the loose board is screwed down into the joist through a pilot hole, the screw head is set below the surface, and the hole is filled to match. On a polished floor the screws are kept in line with the existing nails, so the filled holes disappear into the pattern already there.
From below, where there is a crawl space or a basement, a thin timber wedge is glued into the gap between joist and board, or the board is screwed up from underneath. That fix leaves the top of the floor untouched, which suits a good polished finish.
Two boards that rub along their edges, with no movement on the joist, often go quiet with a fine powder worked into the joint. It is a small fix for a small squeak, and it does nothing for a board that moves.
Timber over a concrete slab
In many apartments the boards sit on timber battens fixed to the concrete. The squeak there tends to be a batten that has worked loose from the slab, or boards that were nailed down without enough adhesive.
The fix is a fixing through the board into a sound batten, or into the slab with the right anchor. Before anyone drills into an apartment slab, they need to know what is inside it, because pipes and cable conduits are often cast into the concrete.
Planks on an underlay
Engineered timber, laminate and hybrid planks are not fixed to anything. They float on an underlay and lock to each other. Screwing them down is the wrong fix.
A creaking floating floor almost always comes from the surface below it. A dip or a hump in the subfloor lets the planks flex at their joins, and a floor laid tight to the walls, with no room to expand, clicks and lifts as it swells. The cure is lifting the planks, levelling the subfloor and relaying with the right gap under the skirting, as covered in [hybrid and vinyl plank flooring in a rental](/blog/hybrid-and-vinyl-plank-flooring-in-a-rental).
Under carpet
With carpet down, the board is fixed through it using a screw made for the job, which snaps off below the pile. The other way is to lift the carpet at the edge and fix the boards before it goes back down.
When new carpet is going in anyway, the boards are screwed down first, because carpet will not stop a board from moving. That step is part of [new carpet in a rental between tenancies](/blog/new-carpet-in-a-rental-between-tenancies).
The finish matters
A squeak fixed with a split board, or a row of clumsy plugs across a polished floor, swaps one problem for another. The fix is done with the same care as the floor itself, and damaged boards are replaced one at a time with matching timber rather than patched.
In a tenanted unit, the noisy part of the job happens inside the building's working hours, and the floor is left clean and ready to walk on before the team leaves.
Related Articles
Tell us about your building.
We will respond with a clear understanding of how we can help.
Get in Touch