Skip to main content
Electrical

Switching From Gas To An Induction Cooktop In An Apartment

John OwenFounder4 min read

Switching an apartment from a gas cooktop to induction starts at the switchboard, not in the kitchen. An induction cooktop needs its own circuit sized to its rating, the gas line has to be capped by a licensed gasfitter, and the benchtop cut-out rarely matches the new unit.

When those three are planned together, the swap is a straightforward job. When they are not, the new cooktop sits in its box while someone works out why it cannot be connected.

The circuit

A gas cooktop needs very little electricity, usually just a plug for the ignition. An induction cooktop is one of the largest loads in an apartment and needs a dedicated circuit run from the switchboard, with its own circuit breaker and safety switch protection.

The cable size and the breaker are set by the cooktop's rating, which is in the manufacturer's installation instructions. That is why the model is chosen before the electrician quotes, not after. In NSW this is licensed electrical work.

The switchboard

Older apartment boards are where these jobs stall. A board with rewireable fuses, no safety switches or no spare space cannot take a new cooking circuit without work of its own.

The detail is in [switchboard upgrades in older buildings](/blog/switchboard-upgrades-in-older-buildings). In practice, the board is checked first and the cooktop is chosen to suit what the board and the unit's supply can carry.

The building's supply

Each apartment's power comes from the building's main switchroom, through a supply that was sized when the building was designed. One unit adding a cooktop is usually fine. Many units doing the same over a few years adds up, which is why some buildings ask about the load before approving new circuits.

In an apartment building, new wiring from the board to the kitchen is work the building manager wants to know about before it starts, so that conversation happens alongside the switchboard check. Running a new circuit in an older unit follows the steps in [adding power points and circuits in older apartments](/blog/adding-power-points-and-circuits-in-older-apartments).

The gas side

The old cooktop is disconnected and the gas line is capped where it enters the kitchen. That is gasfitting work, done by a licensed gasfitter, and the work is certified on completion.

Removing the cooktop does not always end the gas supply to the unit. Some buildings supply gas to a central hot water plant or to heaters in each unit, so the capped line sits next to a supply that is still live. The wider picture of gas in older buildings is in [gas work in older apartments](/blog/gas-work-in-older-apartments).

The benchtop

Gas and induction cooktops rarely share a cut-out size. If the new cut-out is larger, a laminate benchtop can be cut on site, while stone needs proper cutting equipment and care near the edges. If it is smaller, the gap has to be filled or the benchtop section replaced.

Either way, the cooktop sits flat, the edges are sealed, and the cupboard below has the clearance the manufacturer specifies. The benchtop options are in [kitchen benchtop and splashback replacement](/blog/kitchen-benchtop-and-splashback-replacement).

The cooktop itself

The width of the new cooktop has to suit the cabinet below as well as the benchtop, and the manufacturer sets the ventilation and clearance it needs underneath. Some smaller two-zone induction models plug into a standard power point, which avoids a new circuit at the cost of less power across the zones.

For a full-size cooktop in a family kitchen, the dedicated circuit is the right answer.

The rangehood

Induction still produces steam and cooking fumes, so the rangehood stays. The swap is a good time to check it is ducted outside and that it sits at the height the cooktop maker recommends.

In a rental

For a rental, the swap removes a gas appliance from the unit and gives a smooth cooktop that is quick to clean between tenancies. Tenants need cookware with a magnetic base, which is worth stating in the listing and the lease so it is not a surprise on moving day.

One team, one job

A cooktop swap touches the switchboard, a new circuit, the gas line, the benchtop and the rangehood. With one team doing the electrical, the gas, the cutting and the finish in order, the old cooktop comes out and the new one goes in working.

Our electrical work. Talk to us about a property.

JO

John Owen

Founder

Ample Trade, every trade a property needs held by one accountable team on one contact, across the Eastern Suburbs and the Sydney CBD.

ElectricalGasKitchensInductionApartments

Tell us about your building.

We will respond with a clear understanding of how we can help.

Get in Touch