No Power To Part Of An Apartment
When some rooms in an apartment lose power and the others still work, one circuit has switched off at the switchboard. A tripped circuit breaker or safety switch is the most common cause, and if neither one will reset, the fault is in the wiring of that circuit or in the supply coming into the unit.
Each circuit in a home feeds its own group of power points or lights, with its own protection at the board. That is why a fault in a bedroom can leave the kitchen working as normal.
The switchboard
Most apartments have their own switchboard inside the unit, in a hallway, the laundry or a cupboard near the front door. Open the cover and look for a switch that sits in a different position from the ones beside it.
A circuit breaker trips when a circuit carries more current than its cable is rated for, such as a heater and a kettle on the same circuit at once. A safety switch trips when it detects current leaking to earth, which is its protection against electric shock. The difference between the two is set out in [safety switches and electrical testing](/blog/safety-switches-and-electrical-testing).
Older buildings sometimes still have boards with ceramic fuses. A blown fuse looks the same as a working one from the front, so that board is a matter for an electrician, not a tenant with a torch.
One reset
Before resetting anything, unplug the appliances in the rooms that lost power. Then switch the tripped breaker or safety switch fully off and back on.
If it holds, plug the appliances back in one at a time. A switch that trips again the moment one appliance goes back in has found its fault, and that appliance stays unplugged until it is repaired or replaced.
If it trips straight away with nothing plugged in, leave it off. The fault is in the fixed wiring, a power point or a light fitting, and resetting it again and again only strains the switch and the cable. How an electrician traces that fault is covered in [nuisance tripping and finding the fault](/blog/nuisance-tripping-and-finding-the-fault).
When nothing has tripped
Sometimes every switch on the board is on and the rooms are still dead. That points to one of three things.
A loose connection. A cable that has worked loose at a power point, a junction or the board can cut a circuit without tripping anything. It often shows itself first as a power point that feels warm, buzzes or works on and off, the signs listed in [power points that spark, buzz or feel hot](/blog/power-points-that-spark-buzz-or-feel-hot).
A lost phase. Apartment buildings take their supply in three phases, and some units do too. When one phase drops out, every circuit connected to it goes dead while the rest keep working, which can leave half a unit, or a few units on one floor, without power.
The building side. In many blocks, each unit's meter and main switch sit in a meter room or a cupboard on the ground floor or in the corridor. A fault there is a building matter, and the building manager holds the key.
Signs that mean stop
A burning smell, a scorch mark on a switch plate, a crackle from the board or a board that is hot to the touch all mean the same thing. Turn off the main switch if it is safe to reach, keep everyone away from it and call an electrician straight away.
If the neighbours have lost power too, the fault is in the street. Ausgrid manages the electricity network across Sydney's east and posts current outages on its website.
What the electrician does
The electrician isolates the dead circuit, tests the insulation of its cable and checks every connection from the board out to each point and light on it. That finds a cable that has broken down, a damaged power point or a fitting that has let water in.
Repairs to fixed wiring are licensed electrical work in NSW. The circuit is tested before the power goes back on, and the result goes into the property file.
For the property manager
A tenant reporting no power to part of the unit is a priority call, because a fridge or a medical device can be on the dead circuit. Ask which rooms are out, whether anything tripped and what was switched on when it happened. Those three answers, sent with the work order, save the electrician a round of questions at the door.
If the fault turns out to be water in a wall, the electrician is the first trade on it, not the last. The leak, the plaster and the paint follow in that order, and one team working through all of them closes the whole fault rather than its first symptom.
Related Articles
Tell us about your building.
We will respond with a clear understanding of how we can help.
Get in Touch