Does An Older Apartment Need Rewiring?
An older apartment needs rewiring when the cable inside its walls has broken down, and the age of the building alone does not prove that. A licensed electrician tests each circuit, and the results show whether the unit needs a full rewire, a partial one or only a new switchboard.
Plenty of older blocks were rewired decades ago and still test well. Others run on their original cable, and in those it is the insulation around the copper, not the copper itself, that wears out.
What old cable looks like
Buildings wired before plastic-sheathed cable took over often carry rubber-insulated cable. Over the years the rubber hardens, cracks and falls away from the copper, worst of all where it has run warm behind a light fitting or a busy power point.
You will not see any of this from the room. An electrician finds it with the power off, at the back of a switch, inside a light fitting or at the board, where brittle insulation crumbles the moment the cable is moved.
The signs in the unit
These are reasons to have the wiring tested:
- Ceramic fuses at the board instead of circuit breakers
- Scorch marks or brown staining on a power point or switch plate
- Lights that flicker or dim when an appliance starts
- A safety switch that trips in wet weather or for no clear reason
- Too few power points, with powerboards doing the work in every room
- Switch plates or outlets that feel warm to the touch
None of these proves the whole unit needs new cable. Each one is a reason to stop guessing and test it.
How an electrician decides
The board comes first. An old board with ceramic fuses and no safety switches tells the electrician the installation has not been touched in a long time, and the options for that board are set out in [switchboard upgrades in older buildings](/blog/switchboard-upgrades-in-older-buildings).
Then each circuit gets an insulation resistance test. With everything switched off, the tester puts a test voltage on the cable and measures how much current leaks through the insulation, which shows the condition of cable nobody can see. A circuit that passes can stay, and one that fails gets replaced.
A safety switch that keeps tripping is often the first sign of that leakage. Once safety switches are fitted to an old installation, they pick up faults the old fuses never noticed, as covered in [nuisance tripping and finding the fault](/blog/nuisance-tripping-and-finding-the-fault).
Full or partial
A full rewire replaces every circuit, from the board out to each power point and light. It makes sense when most circuits fail the test, or when the unit is being stripped for a renovation and the walls are open anyway.
A partial rewire replaces the circuits that failed and keeps the ones that passed. That is common where the power circuits were redone at some point and the lighting was left on its original cable.
Timing matters as much as the test. Rewiring a kitchen a year after it was refreshed means cutting into new tiles and new paint.
Cable routes in an apartment
A house has a roof space, and often a floor space, to run new cable through. An apartment in a brick block with concrete floors has neither, so the route is planned room by room before anyone starts.
Cable can be chased into a brick wall and patched over, run inside a bulkhead or a cornice, or brought down through a cupboard. Where the old cable sits in a conduit that is still clear, the new cable is pulled through the same path and the wall stays shut. Each choice changes how much plaster and paint work follows.
The trades after the electrician
A rewire leaves chased walls, a hole at every outlet and the odd lifted board. The electrician is finished when every circuit tests clean. The room is finished when the plaster is filled, sanded and painted.
Booked separately, that is three trades with gaps between them while the unit sits half done. Run by one team, the patching follows the cable route room by room, and the unit goes back to the tenant without a trail of open walls.
The paperwork
Rewiring is licensed electrical work in NSW. At the end of the job the electrician issues a Certificate of Compliance for Electrical Work, and it belongs in the property file with the test results and a labelled board.
That record helps at the next sale, the next renovation and the next fault, because the next electrician starts from facts instead of guesses.
When the unit needs more power
A rewire is the right moment to add what the unit lacks. Extra power points where the tenant actually plugs things in, a dedicated circuit for an oven or an air conditioner, and hardwired smoke alarms all go in while the walls are open. The detail on extra circuits is in [adding power points and circuits in older apartments](/blog/adding-power-points-and-circuits-in-older-apartments).
Related Articles
Tell us about your building.
We will respond with a clear understanding of how we can help.
Get in Touch