Replacing Old Shower Taps With A Mixer
Swapping two old shower taps for a single mixer means opening the shower wall, running the hot and cold pipes to one mixer body, sealing the waterproofing around the new opening and tiling over it. The plumbing is the quick part. Most of the planning goes into the wall and the tiles.
A mixer is easier to set, holds a steadier temperature and makes an old bathroom look newer, so it is a common change in a bathroom refresh. It is still a wet-area job, and it has to be treated like one.
More than a tap swap
Old shower taps have one valve for hot and one for cold, each on its own pipe, each through its own hole in the tiles. A mixer has a single body set into the wall at a fixed depth, with both pipes running into it.
So the pipes have to move. The old outlets are capped or cut back, new pipe goes to the mixer position, and the body is fixed so its face sits at the depth the maker sets. Too deep and the handle will not reach. Too shallow and the cover plate stands proud of the tiles.
The mixer itself should be WaterMark certified, and fitting it is licensed plumbing work in NSW.
The membrane
The wall behind a shower is the wettest place in the home, and the waterproofing membrane under the tiles is what keeps water out of the wall frame. AS 3740:2021, the standard for waterproofing domestic wet areas, treats the shower as its highest risk zone.
Every pipe through that wall is a hole in the membrane, and the new mixer adds another. It needs a proper seal around the penetration, with the membrane brought up to it and left to cure before any tile goes back. How that membrane works is in [waterproofing you never see, the membrane under every wet area](/blog/waterproofing-you-never-see-the-membrane-under-every-wet-area).
Opening an old shower wall also shows what is behind the tiles. If there is no membrane, or it has failed, this is the moment to find out, before new tiles go over the top.
The tiles
Tiles from an older bathroom are rarely still made, so a patch of new tiles around the mixer will not match. That leaves three ways to handle it.
Retile a band. Take out a full row or a vertical strip and lay a different tile there on purpose, so it reads as design rather than repair.
Retile the shower wall. Strip the whole wet wall back, waterproof it and tile it new. It is more work, and it gives the cleanest finish.
Fit a cover plate. Some mixers come with a wide plate made to hide old tap holes, which keeps the tile work to a minimum. It only suits walls where the old holes sit in the right place for the new mixer.
Spare tiles from the original job, kept in a cupboard or a storeroom, change this whole decision.
Pressure and temperature
A mixer blends hot and cold inside its body, so it works best when both arrive at a similar pressure. In some older buildings the hot water arrives at a lower pressure than the cold, and a mixer on that supply swings hot and cold whenever someone uses a tap elsewhere. The plumber checks both pressures first and fits a pressure-limiting valve where the supply needs one.
Bathroom hot water is also capped for safety, as set out in [tempering valves and hot water scalding](/blog/tempering-valves-and-hot-water-scalding). The new mixer goes in with that limit in mind.
The order of the job
The water is isolated and the tiles around the old taps come off. The pipes are re-run, the mixer body is fixed, and the whole lot is pressure tested while the wall is still open.
Then the membrane goes on and cures, the tiles go back, and the grout and silicone are finished last. The handle and plate are fitted, and the shower stays out of use until the silicone has cured.
Rushing any step is how a new mixer ends up leaking into the wall, which is the story told in [the leaking shower, why it keeps coming back](/blog/the-leaking-shower-why-it-keeps-coming-back).
One team for the wall
A plumber, a waterproofer and a tiler each own a part of this job, and the wall has to be right for all three of them. When one team holds the whole wall, the pipe that goes through the membrane is sealed by the same people who tile over it, and there is no gap left for the next trade to argue about.
Our tiling and waterproofing work. Talk to us about a property.
Related Articles
Tell us about your building.
We will respond with a clear understanding of how we can help.
Get in Touch