Heated Bathroom Floors And Towel Rails
A heated floor and a heated towel rail change how a bathroom feels in winter. They also help the room dry out after a shower, which matters in older bathrooms that struggle with condensation and mould.
Both are electrical work, and both have to be planned with the tiling and waterproofing around them. Getting the order wrong is how a heating mat ends up buried under new tiles with a fault nobody can reach.
How electric underfloor heating works
The usual system in a bathroom refresh is a thin heating mat or cable laid on the floor, covered in tile adhesive or a thin screed, and tiled over. A thermostat on the wall controls it, reading a sensor set into the floor between the heating cables.
It is designed for comfort, taking the chill off the tiles, rather than heating the whole room. In a small bathroom it can often do both.
The order the work has to happen in
The circuit first. The heating needs its own supply from the switchboard with safety switch protection, run to the thermostat position before the walls are sheeted or tiled. If the switchboard is old, it may need work before it can take a new circuit, which is covered in [switchboard upgrades in older buildings](/blog/switchboard-upgrades-in-older-buildings).
Waterproofing next. The membrane goes down over the floor as normal. In most systems the heating mat sits above the membrane rather than below it, so the membrane stays continuous and is never pierced.
The mat and the sensor. The mat is laid out to avoid the area under the vanity, the toilet and anything else fixed to the floor, because heat trapped under a cabinet does nothing useful and can damage the cable. The floor sensor goes in a conduit so it can be replaced later without lifting tiles.
Testing before tiling. The cable is tested before it is covered, during tiling, and again after. A fault found before tiling costs minutes, while a fault found after costs a floor.
Tiling over it, with care not to nick the cable with a trowel.
Connection and commissioning at the end, with the adhesive given time to cure before the heat goes on.
Insulation and an older floor
On a concrete slab, a lot of the heat goes down into the concrete rather than up into the tiles. An insulation board under the mat lets the floor warm up quicker and use less power.
In an older building with a timber floor, the floor structure, the waterproofing and the height of the finished floor all need checking before heating is added, because a heated floor sits a little higher than the one it replaces.
Heated towel rails
A heated towel rail is a simpler piece of equipment with its own set of decisions.
Hardwired or plug-in. A hardwired rail connects to a concealed outlet and looks cleaner. A plug-in rail needs a power point positioned so the lead does not trail across the wall.
Position. Bathrooms have electrical clearance zones around the bath, shower and basin, and the rail and its connection have to sit where the rules allow.
Control. A timer, or a switch outside the bathroom, means the rail is on when it is useful rather than all day.
Fixing. A rail full of wet towels is a load on the wall, so it needs fixing into studs, noggings or masonry, the same principle as any heavy item on a plasterboard wall.
Condensation and the exhaust fan
A warm floor and a warm towel rail help a bathroom dry out, but they do not replace ventilation. The exhaust fan still has to move moist air out of the room and duct it outside, which is the subject of [bathroom condensation, mould and the exhaust fan](/blog/bathroom-condensation-mould-and-the-exhaust-fan).
In a rental or a hotel
In a rental, a heated towel rail is a small upgrade that tenants notice. Underfloor heating suits a full bathroom refresh, when the floor is coming up anyway, rather than a retrofit under existing tiles.
In a hotel, heated floors and rails are often expected, and the thermostat and timer settings need to be simple for guests and consistent from room to room.
Why it needs one team
Underfloor heating crosses electrical, waterproofing and tiling, and the three have to happen in a strict order with testing at each step. A towel rail crosses electrical and carpentry.
When one team handles all of it, the wiring, the membrane and the tiles follow one sequence, and a fault caught at the testing stage is fixed before a tile goes down. The membrane itself is explained in [waterproofing you never see, the membrane under every wet area](/blog/waterproofing-you-never-see-the-membrane-under-every-wet-area).
Related Articles
Tell us about your building.
We will respond with a clear understanding of how we can help.
Get in Touch