Holes And Dents In Plasterboard Walls
Holes and dents in plasterboard walls are repaired by size: small holes are filled, medium holes are patched with a backing piece, and large damage is cut out and replaced with a new section of sheet. Then the patched wall is sealed and painted from corner to corner, because a spot of paint over a patch almost always shows.
These are the most common repairs at the end of a tenancy. They are also the ones that look worst when rushed.
Small holes
Picture hooks, screw holes from shelves and the marks left by a removed bracket are small holes. Any plug or anchor is pulled out first, then the hole is filled with a plaster filler, left to dry, sanded with 120 grit paper and filled again if it has shrunk.
The second coat is what most rushed repairs skip. Filler shrinks as it dries, and a hole filled once leaves a small dip that shows the moment light falls across the wall.
Dents and door handle holes
A door that swings back hard punches a round hole through the plasterboard where the handle hits. A piece of furniture dragged along a hallway leaves a long dent rather than a hole.
A hole the size of a door handle is too big to fill. It is backed with a piece of plasterboard or a mesh patch, set with a base coat and a topping coat of jointing compound, and feathered out well past the edge of the hole so the repair blends into the wall.
Fixing the cause is part of the job. A door stop on the floor or the skirting stops the handle reaching the wall again, and a door that swings open by itself has a hinge or level problem, which is set out in [doors that drop and hinges that fail](/blog/doors-that-drop-and-hinges-that-fail).
Large damage
A large hole, a section crushed by a fall or a wall soaked by a leak is cut back to a clean square, ideally to the centre of the studs on each side. A new piece of plasterboard of the same thickness, usually 10 mm or 13 mm in a home, is fixed in, then the joins are taped and set in coats, the same way a new wall is finished.
Water-damaged plaster has its own rules, because the leak has to be fixed and the frame dried first. The process is in [plaster repair after a water leak](/blog/plaster-repair-after-a-water-leak).
What is inside the wall
Before cutting into a wall, the electrical cables and copper or PEX water pipes behind it are traced. A wall near a power point or switch almost always has a cable running straight up or down from it, and a wall behind a kitchen or bathroom can carry water pipes.
Older buildings add another check. Some walls that look like plasterboard are fibrous plaster or fibre cement sheet, and older sheeting can contain asbestos. Anything suspect is identified before it is cut or sanded.
Why patches show through paint
A patch can be perfectly flat and still show after painting. Filler and jointing compound absorb paint differently from the painted wall around them, so a patch painted on its own dries with a different sheen. Painters call this flashing.
The fix is to seal every patch with a primer or sealer, then paint the whole wall from corner to corner rather than touching up a square around the repair. Old paint has also faded, so even the original colour from the tin rarely matches the wall it went on years ago. The same reasoning is in [painting over a failed surface](/blog/painting-over-a-failed-surface).
Holes at the end of a lease
For an agent, holes in walls sit right on the line between tenant damage and wear over time. A few small picture hook holes after a long tenancy read differently from a hole punched by a door handle, and the line is drawn in [tenant damage versus fair wear and tear](/blog/tenant-damage-versus-fair-wear-and-tear).
Photos before the repair, and after it, settle that conversation quickly.
One team from patch to paint
A wall repair can involve a carpenter for the door stop, plastering for the patch, an electrician if a cable sits in the way, and a painter to finish. When one team does all of it in order, the wall is repaired, sealed and painted so it looks original, not patched.
Related Articles
Tell us about your building.
We will respond with a clear understanding of how we can help.
Get in Touch