Skip to main content
Plumbing & Gas

Why Flexi Hoses Burst And When To Replace Them

John OwenFounder5 min read

Flexi hoses burst when the steel braid around the rubber tube corrodes, frays or gets kinked, because the rubber cannot hold mains pressure by itself. Replace any hose showing rust, broken strands, a bulge or a sharp bend straight away, and change every hose of unknown age when a unit is empty between tenants.

The hose is the short braided line that joins the water supply to a basin mixer, a kitchen mixer or a toilet cistern. It sits in a dark cupboard and nobody thinks about it until it fails. A dripping tap wastes water slowly, while a burst hose pours at full flow until someone shuts it off, and in an apartment that water reaches the unit below long before anyone reaches the tap.

What is inside a flexi hose

A rubber tube carries the water. A woven stainless steel braid wraps around the tube and holds its shape against the pressure, and a crimped fitting at each end connects it to the valve and the tap.

The braid does the hard work. Once enough strands have rusted through, the rubber balloons out through the gap and splits, which is why a hose can look scruffy for a long time and then let go in a second.

Why they fail

Cleaning products. Bleach and other chlorine-based cleaners give off fumes, and in a closed cupboard those fumes attack the stainless steel. Rust spots on a hose under a kitchen sink often sit right beside the bottles that caused them.

Tight bends and kinks. A hose pushed back against the wall when a vanity goes in, or bent hard right next to its crimp, strains the braid at that point. A hose that is too long and coiled behind a cistern has the same problem.

Overtightening and twist. A nut done up too hard damages the seal, and a hose twisted during fitting holds that twist under load for years.

Age. Rubber hardens and perishes under years of pressure, and the line feeding hot water has the harder life.

Pressure spikes. A tap or a dishwasher valve that snaps shut sends a shock down the pipe, and the hose takes it every time. If the pipes bang, the cause is in [noisy pipes and water hammer](/blog/noisy-pipes-and-water-hammer), and fixing it takes a load off every hose in the unit.

The signs to look for

All it takes is a torch and a look inside each cupboard. These signs mean a hose has reached the end of its life:

  • Brown rust spots or staining on the braid
  • Frayed or broken strands
  • A bulge or a flat spot anywhere along the hose
  • A kink, or a bend tight against the crimp
  • White or green crust around the nut or the crimp
  • A damp cupboard floor, or particleboard that has started to swell

A hose with any of those comes out. Drying it off and leaving it there only moves the failure to a night when nobody is home.

When to replace them

Nobody can tell the age of a hose by looking at it. Some carry a printed date or tag and the maker sets a service life, but older units rarely have any record of who fitted what.

So the replacement points are practical ones. A hose with a warning sign is replaced as soon as it is found. A fixture that comes out for other work goes back on new hoses, because a new vanity on an old hose is how a new bathroom floods. The gap between tenants is the third, since the cupboards are empty and the water can stay off for as long as the job takes.

Washing machine lines are their own case, set out in [laundry connections and what goes wrong](/blog/laundry-connections-and-what-goes-wrong).

The new hose

A flexi hose fitted in Australia should be WaterMark certified, and the mark is on the hose or its tag. It needs to be the right length, long enough to run in a gentle curve with no strain at either end.

Fitting it is licensed plumbing work in NSW. Once the water is back on, each joint is checked for weeping and the cupboard is left dry.

The valve beside it

A hose is only as safe as the valve that stops it. Each fixture should have an isolation valve that shuts off that one line without taking out the whole unit, and on old fixtures those valves are often seized or missing. They are replaced in the same job, for the reasons in [isolation valves and why a building needs them](/blog/isolation-valves-and-why-a-building-needs-them).

When one bursts

Turn off the isolation valve under the fixture, or the main stop tap for the unit if that valve will not move. If water has reached a ceiling light or a power point, turn the power off at the switchboard, as long as you can reach it without standing in water.

Then tell the building manager, because the unit below needs checking straight away. The next steps are in [water coming through a ceiling in an apartment](/blog/water-coming-through-a-ceiling-in-an-apartment).

Across a whole building

Hoses fitted during the same renovation all age together, so one burst is a warning for the rest of the stack. Changing them unit by unit on a set cycle, with a photo of each cupboard before and after, gives a building manager a record of what was done and where. It also beats repairing a ceiling every time the next hose lets go.

More than a hose

A burst rarely stops at the hose. The line gets replaced, a licensed electrician tests the wet circuit, the swollen vanity or skirting comes out, and the ceiling below is cut back, patched and painted.

Sent to one team, that is one list and one invoice, and the owner is not left matching four reports to one leak.

Our plumbing work. Talk to us about a property.

JO

John Owen

Founder

Ample Trade, every trade a property needs held by one accountable team on one contact, across the Eastern Suburbs and the Sydney CBD.

PlumbingFlexi HosesLeaksApartmentsMaintenance

Tell us about your building.

We will respond with a clear understanding of how we can help.

Get in Touch