Can You Mount A TV On A Plasterboard Wall
Yes, but not into the plasterboard on its own. A sheet of plasterboard is a lining, not a structure, and a large TV on a bracket puts a load on it that it was never designed to carry.
The safe way to mount a TV depends on what sits behind the plaster, where the power and cables will go, and in an apartment, what the wall actually is.
What holds the bracket
Timber studs. Most houses and many older apartments have timber stud walls behind the plasterboard. A bracket screwed into the studs with the right fixings is strong and reliable. The catch is that studs sit at set spacings, and the TV position you want may fall between two of them.
Steel studs. These are common in newer apartments and commercial fit-outs. They need different fixings from timber, and a light gauge steel stud holds less in pull-out than a timber one, so a heavy screen may need extra support added inside the wall.
Noggings. When the studs are in the wrong place, the answer is to open the wall, fit timber between the studs at the bracket height, and close it up again. That is carpentry, plastering and painting, and it is the reliable answer for a heavy screen in a chosen spot.
Masonry. Many older Eastern Suburbs apartments have solid brick or concrete walls, sometimes with plasterboard fixed over them. Those need masonry anchors set into the brick or concrete itself, not into the plaster in front of it.
Hollow wall anchors suit light loads. A large TV on a bracket that swings out from the wall is not one of them, because the arm multiplies the load at the fixings every time the screen is pulled forward.
Scanning before drilling
Plasterboard walls hide cables and pipes, and concrete walls can hide conduit. A wall behind a kitchen or bathroom may carry water pipes, and a wall near a switch or power point almost certainly carries a cable running straight up or down from it.
So the wall is scanned and the services are traced before anything is drilled. Hitting a water pipe turns a TV installation into a leak repair, and hitting a cable is a safety problem as well as a repair.
Power and cables
A TV hanging on a wall with cables trailing down to a power point at skirting height looks unfinished. The neat answer is a power point behind the screen and the cables run inside the wall.
Installing a new power point is electrical work, and in NSW it has to be done by a licensed electrician. The TV lead, HDMI and data cables are usually run through a conduit inside the wall, so they can be changed later without opening it up again. The detail on adding circuits in older buildings is in [adding power points and circuits in older apartments](/blog/adding-power-points-and-circuits-in-older-apartments).
If the signal comes from a building antenna or cable system, the wall plate may need to move as well, which brings in [TV antennas and reception in apartment buildings](/blog/tv-antennas-and-reception-in-apartment-buildings).
Apartment walls and strata
Not every wall in an apartment belongs to the lot owner. Walls between units and external walls can be common property, and drilling or chasing into them may need owners corporation approval under the by-laws.
Check before the job. The answer can change where the TV goes, and an internal wall inside the unit, away from the boundary walls and the facade, is usually the simplest choice.
Height and position
The usual mistake is height. Above a fireplace or a tall sideboard it looks good on the plan and strains the neck in use. Eye level from the sofa is the starting point, and the bracket type, whether fixed, tilting or full motion, changes how far the screen sits off the wall.
The position also needs to avoid glare from windows at the times the room is used, which is easier to judge on site than on a floor plan.
In a rental or a hotel
In a rental, a reinforced TV position with a power point behind it is a fixture that lasts across tenancies. Damage from tenants mounting their own brackets into bare plaster is a regular end of lease repair, and the same fixing principles apply to [curtain tracks, blinds and window furnishing fixings](/blog/curtain-tracks-blinds-and-window-furnishing-fixings).
In a hotel room, the bracket, power and cables are installed to one standard, so every room looks the same and the screen cannot be pulled off the wall.
What one team covers
A properly mounted TV can involve carpentry for noggings, electrical work for the power point, cabling, plastering to close the wall, and paint to finish it.
Done in that order by one team, the TV goes on the wall once and the wall looks as if it was built that way.
Related Articles
Tell us about your building.
We will respond with a clear understanding of how we can help.
Get in Touch